Lectrosonics SPNTWB Manual do Utilizador Página 14
- Página / 24
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SPNTWB
LECTROSONICS, INC.
14
Minimum Setup
A required minimum setup is needed to allow the
processor to pass signals and provide acoustic echo
cancellation:
• DenetheInputsandadjustgain
• DenetheCrosspoints
• Denethemixestobeusedassignalsourcesforthe
outputs
• DenetheOutputsandadjustlevels
• ConguretheConferencingConnections
Inputs
Click on the Inputs tab. The setup screen provides con-
trols for gain, signal polarity (phase) and muting, with
level indicators. Connect signal sources and adjust the
gain as needed.
Inputs screen
Input gain slider
Input gain value
Input signal level
Crosspoints
Click on the Mix Matrix tab. Inputs are assigned to
crosspoints which provide the signal sources for the
outputs.
Mix Matrix screen
Stacking Multiple Units
If Slave units are not powered up when the Master unit
boots up, the Slave may not be detected for several
minutes. It is good practice to turn all units on simul-
taneously or turn on Slave units before turning on the
Master unit.
The available processors will appear in a “stack” in the
control panel. The Master unit details will appear at the
top, with Slave units below it appearing in the order that
they are connected with the cable connections to the
ASPEN port jacks.
The Master
unit connected
directly
The Master
and Slaves
connected
below it
Click OK to
open the control
panels
Refer to the cabling diagram for the ASPEN ports in the
section entitled Hardware Installation.
Using the Control Panel
To connect to connect a running ASPEN device, choose
a connection method from the Connect menu: USB,
Network or Serial. The device can be configured di-
rectly when connected.
USB, Network or Serial
To work on a system design project, choose an option
from the Project menu. You may create a new project or
open an existing project.
Choose Help->ASPEN Online Help... to open an
extensive Help system describing the may features and
functions of the Control Panel program.
- IMPORTANT 1
- LECTROSONICS, INC 2
- Important Safety Instructions 3
- Inspection of the Unit 3
- Introduction 4
- Table of Contents 5
- Front Panel 6
- Rear Panel 7
- Hardware Installation 8
- Programmable Inputs 9
- Programmable Outputs 9
- Audio Outputs 9
- Power Amp Outputs 9
- Crestron 10
- and AMX 10
- Port Wiring Diagram 10
- Cabling Of Stacked Units 10
- Software Installation 11
- Refer to the Help Files 11
- Creating an ASPEN 11
- Installer Disk 11
- Software and Firmware 12
- Firmware Update 12
- Procedure 12
- Update Procedure 13
- Minimum Setup 14
- Stacking Multiple Units 14
- Using the Control Panel 14
- Output Sources 15
- Conference Connections 15
- Acoustic Echo Canceller 15
- The Signal Flow Screen 16
- Rio Rancho, NM 17
- Using the LCD 18
- Master Reset 19
- LCD Categories and 20
- Settings 20
- Network Setup 21
- Web Browser Interface 21
- Service and Repair 22
- INDUSTRY CANADA NOTICE 23
- LIMITED THREE YEAR WARRANTY 24
Manuais e produtos relacionados com Acessórios áudio Lectrosonics SPNTWB
(16 páginas)AEG KS7400021M manuels
Manuels d'utilisation et guides de l'utilisateur pour Mesure, test et contrôle AEG KS7400021M.
Nous fournissons des manuels en pdf 2 AEG KS7400021M à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais